This is ma first attemp 2 make a Bedini Motor...


oke, first pic...yes that is the Daftman Bedini Diagram ima using...its turning about 300/400 RPM...not a ferrari but atleast its turning.
when i finished putting the system 2gether i took away the paper Daftman Diagram that i have glue to the board so i must memorise the Diagram.(learning process)
ma transistor is floating in the air...not attach to the board or anything(dont know if this is good or not) it does not heat up.
ma Telsa coil is rubish...just 2 coil of wire i bought and just made a coil from it.
i think on the 0.6mm(run) wire theres only about 200 windings and on the 0.25mm(trigger) wire about 300 windings.
the center of the coil is made with nails.
ma rotor is a CD player rotor and 2 CD`s glue 2gether and 12 magetes(weak ones)
3 magetes glue 2gether and on 4 of these packs on the Norht/South/West and East side on the CD`s.(hope this makes any sence??)
ma setup is kinda rude at this moment but ima very happy with the results

its running on a 9.6 volt - 0.7Ah rechargeble battery from ma radio control car.
the light bulp is glowing kinda orange non stop.
i did put another rechargeble battery(4.8 volt) on it by the B-Emf and the bulp stop glowing.
ma only question is how come its glowing becoz its a 90 V neon bulp and ma setup is not likely to generate that muck of voltage??
maybe the store sold me a 15 volt 1???...when i told them i was building a Bedini Motor they looked at me like ima some kinda Alien...anyway

i couldnt messure the Milli Amp becoz ma 2 units only goes to 200 and 250 milli Amps.
if i try 2 messure it the needle just goes all the way at the end.(time for a better messure instruments or ima doing it wrong)



here u can see ma input is 10.00 volt...btw do not look at ma wirering colors(very confusing) next time i will do better color codes...:)



here u can see ma output is 8.08 Volt...not overunity yet

the date on the pics is wrong i did not adjusted the date when i put in new battries in the Cam.
pics were made 2day...02-04-09.

well i hope i didnt 4get anything...any info is gladly recived(not the nasty ones ofcourse)

============================================
============================================
============================================

this here setup below is ma second Bedini setup made 2day(02-04-09) using the Daftman Diagram...much more clean and i use a different kinda wire connection.
this wire connection type(dont know how its called those white thingies with screws in them) suits me better but i dont know how it will work.
as 1 can see i have put 5 new things in it...
1 - a on/of switch for the power source.
2 - a 12V light bulp(from a car) on the Back Emf(Output) to reduce the load on my neon bulp.
3 - a 12v light bulp(from a car) on the Primary(Input) just to see that i have power when switch on.
4 - a piece of paper on the 1K resistor with S 4 slow and F 4 fast.
5 - a piece of none magnetic metal below the transistor.

the purple wire is suppose to b blue but i ran out of blue wire...the rest is equal to the Daftman Diagram.

another thing is the In4001 diode is In4002 becoz the store didnt have the In4001 1 :-\\



i can not test it becoz ma coil is damage and ima building a new better rotor aswell.
i did get ma neodym magnetes 2day but they r 2 small...strong but still 2 tiny.
i am gonna order new wire and magnete 2morrow so hopefully this Motor will b ready by the end of next week...hopefully sooner.

and i also need 2 12volt battery aswell from a car or motorcicle.

than we will see if ma Bedini Motor can run good...



as 1 can see i have trash 3 old VCR for their Rotor...these things r really the best...perfectly balance.
i have put 1 in the center of another MDF board...i have left some room on the Bedini board for the Bat-Swap from Daftman.
now i need to make a disk out of MDF or find something from plastic or any none magnetis material.
i have decided to use the Neodym magnetes that i have now...all tho they r small but they r very strong so i think they will do the trick.
i have found a website...http://www.conrad.com/ but the ducth 1(.nl)...there i found everything for the Bedini Motor except 4 the neon bulp(they only have the 230v ones).
wire has been order...while w8ting for the wire i will focos on the Rotor.
thats it 4 now...



as 1 can see below i have made 2 Bedini Circuit with the Daftman Diagram.
i now have all the components complete but none of the 2 wants 2 spin like my first 1...i do think that i have wire it wrong(both) at some point.
gonna check and recheck till they worked.
if some of u see the problem do replay(ty).


heres my rotor made from a VCR head and wood(mdf) with 8 NeoDym Magnete.
it is very smooth spinning.(by the hand at this moment)


another look at the rotor :)).


Cheers & Tumbs Up 4 The Daftman